LoRa APRS Track Direct

☰

reset

SP8MB-L Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP8MB-L. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1756551896	578 Count	85 Count	78 Count
1756551775	577 Count	85 Count	78 Count
1756551654	575 Count	84 Count	77 Count
1756551532	574 Count	84 Count	77 Count
1756551411	573 Count	84 Count	77 Count
1756551290	572 Count	84 Count	77 Count
1756551169	571 Count	84 Count	77 Count
1756551049	570 Count	84 Count	77 Count
1756550928	569 Count	84 Count	77 Count
1756550807	567 Count	83 Count	76 Count
1756550686	566 Count	83 Count	76 Count
1756550565	565 Count	83 Count	76 Count
1756550444	564 Count	83 Count	76 Count
1756550323	563 Count	82 Count	76 Count
1756550202	561 Count	81 Count	75 Count
1756550081	560 Count	81 Count	75 Count
1756549961	559 Count	81 Count	75 Count
1756549840	557 Count	80 Count	74 Count
1756549719	556 Count	80 Count	74 Count
1756549598	555 Count	80 Count	74 Count
1756549477	554 Count	80 Count	74 Count
1756549356	553 Count	80 Count	74 Count
1756549235	552 Count	80 Count	74 Count
1756549115	551 Count	80 Count	74 Count
1756548994	550 Count	80 Count	74 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time:

Maintained by I8FUC, based on APRS Track Direct