LoRa APRS Track Direct

☰

reset

SQ2SIX-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ2SIX-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TX*	RX*	Digi*
1754318143	144 Count	900 Count	144 Count
1754317544	144 Count	893 Count	144 Count
1754316943	144 Count	889 Count	144 Count
1754316343	144 Count	885 Count	144 Count
1754315743	143 Count	876 Count	143 Count
1754315143	143 Count	872 Count	143 Count
1754314543	143 Count	868 Count	143 Count
1754313943	142 Count	861 Count	142 Count
1754313343	142 Count	857 Count	142 Count
1754312743	142 Count	851 Count	142 Count
1754312143	142 Count	843 Count	142 Count
1754311543	142 Count	837 Count	142 Count
1754310943	142 Count	830 Count	142 Count
1754310342	142 Count	823 Count	142 Count
1754309743	142 Count	819 Count	142 Count
1754309142	142 Count	815 Count	142 Count
1754308542	141 Count	807 Count	141 Count
1754307942	141 Count	800 Count	141 Count
1754307342	141 Count	795 Count	141 Count
1754306742	141 Count	788 Count	141 Count
1754306142	141 Count	784 Count	141 Count
1754305542	141 Count	778 Count	141 Count
1754304942	139 Count	769 Count	139 Count
1754304342	139 Count	765 Count	139 Count
1754303742	139 Count	762 Count	139 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time:

Maintained by I8FUC, based on APRS Track Direct