LoRa APRS Track Direct

☰

reset

IU3ISP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IU3ISP-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TX*	RX*	Digi*
1761548090	5 Count	56 Count	5 Count
1761546287	114 Count	1028 Count	80 Count
1761544483	109 Count	971 Count	76 Count
1761542679	104 Count	943 Count	72 Count
1761540875	102 Count	928 Count	71 Count
1761539071	98 Count	879 Count	68 Count
1761537267	95 Count	838 Count	66 Count
1761535463	91 Count	793 Count	63 Count
1761533659	86 Count	747 Count	59 Count
1761528292	71 Count	614 Count	51 Count
1761526487	66 Count	574 Count	47 Count
1761524683	65 Count	556 Count	47 Count
1761522880	62 Count	521 Count	45 Count
1761521076	56 Count	478 Count	40 Count
1761519272	51 Count	420 Count	36 Count
1761515664	45 Count	352 Count	32 Count
1761513860	42 Count	309 Count	30 Count
1761512056	39 Count	274 Count	28 Count
1761508449	33 Count	223 Count	24 Count
1761506689	26 Count	184 Count	22 Count
1761504885	23 Count	143 Count	20 Count
1761503081	21 Count	101 Count	19 Count
1761501277	18 Count	72 Count	17 Count
1761499473	12 Count	32 Count	12 Count
1761494062	163 Count	940 Count	120 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time:

Maintained by I8FUC, based on APRS Track Direct